Clarinet Systems ESB101 Podręcznik Użytkownika Strona 32
- Strona / 71
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
3-12
AP. In the case of 128-bit encryption, The
Default Tx Key will always be 1 and AP
must be configured to used 1 if multiple keys are allowed for 128-bit encryption.
Note: 128-bit encryption will have performance decrease compare to 64-bit encryption.
Updating The Firmware
Periodically, Clarinet Systems engineers make improvements to the functionality of
the EthIR Switch via firmware updates. These can be freely downloaded from
Clarinet Systems web site.
To update the firmware in the Configuration Tool:
1.
Initiate either an Ethernet communication session to the switch in need of
updating as described in Configure via IP address on page 3-4.
2.
Locate the EthIR Switches as described in Searching For EthIR Switches on
page 3-6
. Alternately, if you wish to manage only one Switch in your LAN
system, you can click the
Find One Switch button and enter the specific IP
address of that Switch.
3.
Select the Switch you want to update from the list of available switches on the
Tool dialog. You can select multiple Switches by holding the control key and
clicking on the desired Switches.
4.
Once you select a Switch, the Update Firmware button will be enabled.
5.
Click Select File to navigate to the file containing a image (wrp file) that was
either downloaded or sent to you from Clarinet Systems. Click the
Update
Firmware button. If no file is selected, you are prompted to select a file.
Once a file is chosen, all the selected Switches are updated in sequence. Once
the upgrade is complete the switch is automatically rebooted.
Note: Try to update the firmware after work or at light traffic since the Switch will reboot
itself after updating and any infrared sessions taking place will terminate. The update and
reboot process takes about one minute for each Switch. If a group of Switches are selected,
then the update will take one minute for each Switch in sequence.
Switch Security
All switches of EthIR LAN family contain security option that prevent unauthorized
individuals to view and modify the switch configuration. This option can be enabled
by click on the
Set Switch Password button on the configuration tool. Once set, all
configuration operation will require the user to enter the proper password to continue.
The
Set Switch Password button can also be used to disable password. If at any
given time the switch password is lost, please free to contact Clarinet Systems Tech
Support to obtain a default password for the switch. “RADIUS Security” is an
optional feature should be considered to provide further security protection.
- EthIR LAN 1
- User Guide 1
- EthIR LAN® User Guide 3
- TABLE OF CONTENTS 5
- Chapter 1 9
- Introduction 9
- Appendices 10
- Conventions 10
- Contacting Clarinet Systems 11
- Chapter 2 13
- Installation 13
- Figure 2-1 15
- N/A N/A N/A ON N/A 17
- 216 only) 18
- EthIR Beam 19
- ClarinetIR™ 20
- CSI Firmware updates 20
- Chapter 3 21
- Configuring EthIR LAN 21
- Configure via Infrared 23
- Configure via IP address 24
- Searching For EthIR Switches 26
- The NVM Editor 28
- SNMP Variables Tab 29
- RF Card Info (ESB3011B only) 30
- WEP (ESB3011b only) 31
- Updating The Firmware 32
- Switch Security 32
- Chapter 4 33
- ClarinetIR 33
- APPENDIX A 35
- APPENDIX B 41
- APPENDIX C 43
- APPENDIX D 45
- APPENDIX E 47
- APPENDIX F 51
- Infrared Monitor as follows: 52
- Microsoft IrLAN 54
- Notebooks 55
- Add/Remove Program icon in 56
- Add/Remove dialogs: 56
- Details button 57
- Click OK 58
- Direct Cable Connection 58
- Guest then click the Next 58
- Cancel 59
- File\Desktop 66
- Shortcut 66
- and click 67
- Apple Menu\Control 68
- Configuring Palm Organizers 69
Compex WPE54G Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Router Compex WPE54G.
Wir stellen 1 PDF-Handbücher Compex WPE54G zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Spezifikationen
Komentarze do niniejszej Instrukcji